Category Archives: Fire Bricks

Concise User’s Instructions STANDARD COL. FIREPLATES SK32 Al2O3 38%, 500x250x60mm

Print This Post Print This Post

 

Thank you for choosing our products.

 

The following instructions will help you make the most out of our quality.

 

STANDARD COL. FIREPLATES SK32 Al2O3 38%, 500x250x40mm

 

  1. Description: Fireclay-based, Semi-dry pressed , low-porosity, ceramic-bonded firebrick with 35% Alumina content.

 

2. Classification: FC 40

 

  1. General installation instructions:
    1. Diamond blade water cut is recommended.
    2. Bricks that have got wet could be used after drying.
    3. Bricks can be stored preferably in covered area but can also be stored in the open air.
    4. Pallet stacking is admissible and the loaded pallets must not exceed 3 pallets.
    5. “First in – First out” management of stored bricks is advisable.
    6. The key brick (closure of arches) and its placement requires a particular attention. Detailed instructions could be available upon your request.
    7. The preheating diagrams are available on request from our Technical Service Department.

The final User must follow carefully the instructions of Designer of the specific project.

 

 

Print This Post Print This Post

Concise User’s Instructions RED FIREBRICKS SK32 Al2O3 38%, 220x110x40 mm

Print This Post Print This Post

 

Thank you for choosing our products.

 

The following instructions will help you make the most out of our quality.

 

RED FIREBRICKS SK32 Al2O3 38%, 220x110x40 mm

 

  1. Description: Fireclay-based, Semi-dry pressed , low-porosity, ceramic-bonded firebrick with 35% Alumina content.

 

2. Classification: FC 40

 

  1. General installation instructions:
    1. Diamond blade water cut is recommended.
    2. Bricks that have got wet could be used after drying.
    3. Bricks can be stored preferably in covered area but can also be stored in the open air.
    4. Pallet stacking is admissible and the loaded pallets must not exceed 3 pallets.
    5. “First in – First out” management of stored bricks is advisable.
    6. The key brick (closure of arches) and its placement requires a particular attention. Detailed instructions could be available upon your request.
    7. The preheating diagrams are available on request from our Technical Service Department.

The final User must follow carefully the instructions of Designer of the specific project.

 

 

Print This Post Print This Post

Concise User’s Instructions RED FIREBRICKS SK32 Al2O3 38%, 220x55x40 mm

Print This Post Print This Post

 

Thank you for choosing our products.

 

The following instructions will help you make the most out of our quality.

 

RED FIREBRICKS SK32 Al2O3 38%, 220x55x40 mm

 

  1. Description: Fireclay-based, Semi-dry pressed , low-porosity, ceramic-bonded firebrick with 35% Alumina content.

 

2. Classification: FC 40

 

  1. General installation instructions:
    1. Diamond blade water cut is recommended.
    2. Bricks that have got wet could be used after drying.
    3. Bricks can be stored preferably in covered area but can also be stored in the open air.
    4. Pallet stacking is admissible and the loaded pallets must not exceed 3 pallets.
    5. “First in – First out” management of stored bricks is advisable.
    6. The key brick (closure of arches) and its placement requires a particular attention. Detailed instructions could be available upon your request.
    7. The preheating diagrams are available on request from our Technical Service Department.

The final User must follow carefully the instructions of Designer of the specific project.

 

 

Print This Post Print This Post

Concise User’s Instructions RED FIREBRICKS SK32 Al2O3 38%, 220x110x60 mm

Print This Post Print This Post

 

Thank you for choosing our products.

 

The following instructions will help you make the most out of our quality.

 

RED FIREBRICKS SK32 Al2O3 38%, 220x110x60 mm

 

  1. Description: Fireclay-based, Semi-dry pressed , low-porosity, ceramic-bonded firebrick with 35% Alumina content.

 

2. Classification: FC 40

 

  1. General installation instructions:
    1. Diamond blade water cut is recommended.
    2. Bricks that have got wet could be used after drying.
    3. Bricks can be stored preferably in covered area but can also be stored in the open air.
    4. Pallet stacking is admissible and the loaded pallets must not exceed 3 pallets.
    5. “First in – First out” management of stored bricks is advisable.
    6. The key brick (closure of arches) and its placement requires a particular attention. Detailed instructions could be available upon your request.
    7. The preheating diagrams are available on request from our Technical Service Department.

The final User must follow carefully the instructions of Designer of the specific project.

 

 

Print This Post Print This Post

Concise User’s Instructions RED FIREBRICKS SK32 Al2O3 38%, 220x55x60 mm

Print This Post Print This Post

 

Thank you for choosing our products.

 

The following instructions will help you make the most out of our quality.

 

RED FIREBRICKS SK32 Al2O3 38%, 220x55x60 mm

 

  1. Description: Fireclay-based, Semi-dry pressed , low-porosity, ceramic-bonded firebrick with 35% Alumina content.

 

2. Classification: FC 40

 

  1. General installation instructions:
    1. Diamond blade water cut is recommended.
    2. Bricks that have got wet could be used after drying.
    3. Bricks can be stored preferably in covered area but can also be stored in the open air.
    4. Pallet stacking is admissible and the loaded pallets must not exceed 3 pallets.
    5. “First in – First out” management of stored bricks is advisable.
    6. The key brick (closure of arches) and its placement requires a particular attention. Detailed instructions could be available upon your request.
    7. The preheating diagrams are available on request from our Technical Service Department.

The final User must follow carefully the instructions of Designer of the specific project.

 

 

Print This Post Print This Post

Concise User’s Instructions RED FIREBRICKS SK32 Al2O3 38%, 220x110x30 mm

Print This Post Print This Post

 

Thank you for choosing our products.

 

The following instructions will help you make the most out of our quality.

 

RED FIREBRICKS SK32 Al2O3 38%, 220x110x30 mm

 

  1. Description: Fireclay-based, Semi-dry pressed , low-porosity, ceramic-bonded firebrick with 35% Alumina content.

 

2. Classification: FC 40

 

  1. General installation instructions:
    1. Diamond blade water cut is recommended.
    2. Bricks that have got wet could be used after drying.
    3. Bricks can be stored preferably in covered area but can also be stored in the open air.
    4. Pallet stacking is admissible and the loaded pallets must not exceed 3 pallets.
    5. “First in – First out” management of stored bricks is advisable.
    6. The key brick (closure of arches) and its placement requires a particular attention. Detailed instructions could be available upon your request.
    7. The preheating diagrams are available on request from our Technical Service Department.

The final User must follow carefully the instructions of Designer of the specific project.

 

 

Print This Post Print This Post

Concise User’s Instructions RED FIREBRICKS SK32 Al2O3 38%, 220x55x30mm

Print This Post Print This Post

 

Thank you for choosing our products.

 

The following instructions will help you make the most out of our quality.

 

RED FIREBRICKS SK32 Al2O3 38%, 220x55x30mm

 

  1. Description: Fireclay-based, Semi-dry pressed , low-porosity, ceramic-bonded firebrick with 35% Alumina content.

 

2. Classification: FC 40

 

  1. General installation instructions:
    1. Diamond blade water cut is recommended.
    2. Bricks that have got wet could be used after drying.
    3. Bricks can be stored preferably in covered area but can also be stored in the open air.
    4. Pallet stacking is admissible and the loaded pallets must not exceed 3 pallets.
    5. “First in – First out” management of stored bricks is advisable.
    6. The key brick (closure of arches) and its placement requires a particular attention. Detailed instructions could be available upon your request.
    7. The preheating diagrams are available on request from our Technical Service Department.

The final User must follow carefully the instructions of Designer of the specific project.

 

 

Print This Post Print This Post